Power On and Verification After installing the Fill-Rite hardware and restoring power to the pump, verify the following items: 1. Power to the Hardware Check that there are lights on the Fill-Rite circuit board and that the LEDs are illuminated on the circuit board: If the board does not have power, check that the circuit […]
⚠ Warning: Do not attach AC power to the terminal marked “12V+”. This terminal is for DC active pulsers only. Attaching AC power to this terminal will destroy your Fill-Rite board. The wiring configuration for pulsers depends on whether you are using a passive pulser or an active pulser. All pulser wiring should be connected […]
⚠ Warning: Do not attach AC power to the terminal marked “12V+”. This terminal is for DC active pulsers only. Attaching AC power to this terminal will destroy your Fill-Rite board. The wiring configuration for pulsers depends on whether you are using a passive pulser or an active pulser. All pulser wiring should be connected […]
Fill-Rite interfaces with dispensers, meters, and registers through programmable pulse outputs. Most mechanical dispensers, meters, and registers have a pulse output capability or a way to add a pulse output. This is done by adding a pulser if you have not had a fuel management system before, but we can help with that. Is my […]
Fill-Rite Hardware Power In / Power Out Fill-Rite piggybacks power off the AC input. Your wiring configuration will depend on whether the pump runs on AC or DC power. For use with DC applications a Class 2 power supply is required for the board’s power. DC DC input requires ~12V DC. Attached positive power to […]
Fill-Rite Hardware Power In / Power Out Fill-Rite piggybacks power off the AC input. Your wiring configuration will depend on whether the pump runs on AC or DC power. For use with DC applications a Class 2 power supply is required for the board’s power. DC DC input requires 8-50V DC. Attached positive power to […]
Hazardous Areas – Where NOT to mount Site Controller or Expansion Module DO NOT mount the Site Controller or any Fill-Rite FMS device within the hazardous / classified area: Class I Div 1 (Zone 1) or Class I Div 2 (Zone 2): Dispensing DeviceClass 1 Div 1Class 1 Div 2Compressed Natural Gas (CNG)Entire space within […]
Dimensions: • 14.96″ x 11.02″ x 5.12″ • 379.98mm x 279.91mm x 130.05mm Note: The NXFM150 must be mounted 18″ away from a Class 1 div 1 area. Pumps that are connected to the NXFM150 need to be within Wi-Fi range of the NXFM100.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed […]
All peripheral equipment connected to the NXFM100 system must be UL and CSA listed.
The NXFM100 contains a rechargeable battery. If the battery needs to be replaced, please contact Fill-Rite, or have an authorized technician service them.
Wireless Encryption and Security The NXFM100 wireless network uses WEP security with AES-128 protocol encryption to prevent unwanted packet sniffing. Wi-Fi Signal Strength The Fill-Rite app requires line-of-sight to the NXFM100 in order to communicate. The total wireless range of the NXFM100 is 150 feet.To ensure the best performance of the NXFM100, do not install […]
Dimensions: • 12.59″ x 10.59″ x 7.11″ • 32.0cm x 26.9cm x 18.1cm The NXFM100 has 4 holes that allow it to be mounted in various setups. Note: The NXFM100 must be mounted 18″ away from a Class 1 div 1 area. For mobile devices to connect to the NXFM100, they must be within 300 […]
NXFM100 SpecificationsPower Requirements100-240VAC, 50/60Hz, 3600W8-50 VDC, 1500WDC requires a Class 2 power sourcePump Control Ratings1HP, 125VAC2HP, 240VAC125VAC, 30A General Purpose240VAC, 15A General Purpose8-50VDC, 30FLA/90LRA8-50VDC, 30A General PurposeDimensionsH: 8″W: 11.5″D: 5.75″Weather RatingsNEMA 4X / IP67Temperature Ratings-4 F to 122 F (-20 C to 50 C) UL Installations-40 F to 140 F (-40 C to 60 C) […]
Click each question below to open/close its answer How do I wire the pulser?Please refer to this Pulser Troubleshooting Guide or the Pulser Compatibility Guide (each PDF will open in its own browser tab). Fill-Rite works with several pulser options. Each pulser varies slightly in terms of wiring. Do I have to use the DAF […]
From the Dashboard Select ‘Settings’ Select ‘Users’ Select the user you would like to delete Select the Delete button Say yes to the Are you sure? message
Each account can have multiple Users. If you want someone else to be able to log in to your account, you can add them as a User in the Settings section. To add a New User:
The App Timer is the time allocated for the entire transaction lifecycle. You can turn this timer off under the account settings portion of the Fill-Rite website. This timer is configurable between 5 minutes and 25 minutes.
Two Factor Authentication is when drivers are required to scan their QR code and Enter their PIN. To turn on Two Factor Authentication go to Settings-App settings.
From the Billing section in the Settings tab, you can view estimates for your upcoming invoice, check your next billing date and current subscriptions, view your billing history, and edit your billing information. Additional Billing Contacts The account owner will always receive invoices and billing-related emails. If you want someone else to receive billing emails […]